Fighter Jet
ProductOverview
A fighter jet is built to win the fight for control of the air: to detect, out-maneuver, and shoot down other aircraft, and increasingly to strike ground targets as well. Every choice on the airframe trades against agility, speed, sensor reach, and survivability. This aircraft pairs a single afterburning Afterburning Turbofan with a Airframe shaped to reduce its radar signature, an AESA AESA Radar for long-range detection, a quadruplex Fly-by-Wire Flight Controls system that lets it fly at the edge of stability, and a Weapon System carrying guns and missiles. A Cockpit & Life Support with an ejection seat keeps the one pilot alive and in command of all of it.
Propulsion
Thrust decides whether a fighter can climb, accelerate, and sustain a turn, so the Afterburning Turbofan is a low-bypass afterburning turbofan tuned for power over fuel economy. Air enters through serpentine Air Intake (S-duct) S-ducts that hide the compressor face from enemy radar, passes through the Fan Module and the high-pressure High-Pressure Compressor, and burns in an annular Annular Combustor. The High-Pressure Turbine and Low-Pressure Turbine extract work to drive the compressor and fan. For maximum thrust the Afterburner injects raw fuel into the hot exhaust through a Fuel Spray Bar manifold and burns it behind a Flame Holder, and the Variable Exhaust Nozzle varies its throat area with actuated Nozzle Petal petals to match the engine's operating point. A FADEC Engine Control manages the whole engine so the pilot can slam the throttle without stalling the compressor.
Airframe and stealth
The Airframe mixes titanium and composite to survive high g-loads at low weight. The Wing carries a Leading-Edge Flap and an Aileron, while pitch and roll authority at high angle of attack comes from an all-moving All-Moving Horizontal Tail. Low observability is shaped into the structure: aligned edges, buried intakes, internal weapon carriage, and a Radar-Absorbent Coating radar-absorbent coating over the skin. Stealth is a design discipline rather than a single part, so the Internal Weapons Bay weapons bays and the flush antennas matter as much as the coating.
Avionics and sensors
The Avionics Suite suite is what turns a fast airplane into a weapon. The AESA Radar uses around a thousand gallium-nitride T/R Module modules to steer its beam electronically, tracking many targets at once and resisting jamming. A passive Infrared Search & Track infrared search-and-track finds targets that run with their own radars off. The Electronic Warfare Suite electronic warfare system combines a Radar Warning Receiver radar warning receiver, a Self-Protection Jammer, and a Chaff/Flare Dispenser for chaff and flares. A redundant Mission Computer fuses these feeds and a Tactical Datalink shares the picture with other aircraft, so a flight of fighters sees as one.
Flight controls
A modern fighter is deliberately unstable in pitch, which makes it agile but impossible to fly by hand. A Fly-by-Wire Flight Controls system with four redundant Flight Control Computer channels reads the pilot's HOTAS Controls inputs and the IMU (6-axis) motion sensors, then commands the Surface Hydraulic Actuator hydraulic actuators hundreds of times a second to hold the aircraft where the pilot points it. The same system enforces the +9 g limit so the airframe is never overstressed, and it keeps the jet controllable at high angles of attack where an older aircraft would depart into a spin.
Cockpit and survivability
The Cockpit & Life Support gives one pilot command of the whole system through a Head-Up Display head-up display, three Multifunction Display multifunction displays, and a Helmet-Mounted Display that projects targeting symbols onto the visor so the pilot can aim a missile by looking at the target. An Onboard Oxygen Generator onboard oxygen generator removes the need for liquid oxygen bottles. If the aircraft is lost, the zero-zero Ejection Seat fires a Rocket Catapult to throw the pilot clear even at zero speed and zero altitude, then deploys a Seat Parachute automatically.
Armament, landing gear, and systems
The Weapon System carries an internal rotary Rotary Cannon for close combat and a mix of missiles and bombs on eleven Wing Hardpoint hardpoints plus the internal bays. A Stores Management System computer arms, selects, and releases each weapon. The Landing Gear is a reinforced tricycle layout with carbon Carbon Wheel Brake brakes and an Arrestor Hook for emergency runway arresting. Two engine-driven Integrated Drive Generator generators feed the Electrical System system, and dual Hydraulic System systems at 4,000 psi power the flight controls and gear. Roles split across variants: an air-superiority fit emphasizes radar and missiles, a strike fit adds targeting pods and ground-attack stores, and a carrier variant strengthens the gear and adds the arrestor hook and folding wings. Pilots train for years to use the airframe's full envelope, because the aircraft can pull more g and point its nose faster than an untrained body can withstand or a careless hand can manage.
Fighter Jet parts and their functions
10 top-level parts · 4,776 parts in total · full bill of materials below| # | Part | Qty | What it does |
|---|---|---|---|
| 1 | Afterburning Turbofan 9 parts | 1× | Afterburning turbofan |
| 2 | Airframe 7 parts | 1× | Fuselage and wings |
| 3 | Cockpit & Life Support 7 parts | 1× | Cockpit and life support |
| 4 | Avionics Suite 6 parts | 1× | Radar, sensors, computers |
| 5 | Fly-by-Wire Flight Controls 4 parts | 1× | Fly-by-wire actuation |
| 6 | Landing Gear 6 parts | 1× | Retractable gear |
| 7 | Fuel System 5 parts | 1× | Internal fuel |
| 8 | Weapon System 5 parts | 1× | Pylons, gun, and stores management |
| 9 | Hydraulic System 4 parts | 1× | Flight control hydraulics |
| 10 | Electrical System 5 parts | 1× | Generation and distribution |
3D model
No 3D model yet. Have a CAD file of this? Add a 3D model. STL renders right on this page; STEP, FreeCAD, and OpenSCAD sources are welcome too (openly licensed, like all 3D models on BOMwiki).
Build & assembly graph
expand / collapse · shared sub-assemblies converge · links to related products · est. labourTap an assembly to expand/collapse · tap a part to open it · use “Open page” for any node · drag to pan, scroll to zoom.
Bill of materials for Fighter Jet
10 top-level lines · 144 rows shown · 4,776 parts total · indented to 3 levels| # | Item / sub-assembly | Part no. | Qty/assy | Ext. qty | Parts | Type |
|---|---|---|---|---|---|---|
| 1 | Afterburning Turbofan 9 parts | fighter-jet-engine | 1× | 1 | 885 | assembly |
| 1.1 | Fan Module 3 parts | fighter-jet-fan | 1× | 1 | 64 | assembly |
| 1.1.1 | Fan Disk | fighter-jet-fan-disk | 3× | 3 | · | part |
| 1.1.2 | Fan Blade | fighter-jet-fan-blade | 60× | 60 | · | part |
| 1.1.3 | Fan Containment Case | fighter-jet-fan-case | 1× | 1 | · | part |
| 1.2 | High-Pressure Compressor 4 parts | fighter-jet-compressor | 1× | 1 | 387 | assembly |
| 1.2.1 | Compressor Disk | fighter-jet-compressor-disk | 6× | 6 | · | part |
| 1.2.2 | Compressor Blade | fighter-jet-compressor-blade | 200× | 200 | · | part |
| 1.2.3 | Stator Vane | fighter-jet-compressor-vane | 180× | 180 | · | part |
| 1.2.4 | Compressor Case | fighter-jet-compressor-case | 1× | 1 | · | part |
| 1.3 | Annular Combustor 3 parts | fighter-jet-combustor | 1× | 1 | 23 | assembly |
| 1.3.1 | Combustor Liner | fighter-jet-combustor-liner | 1× | 1 | · | part |
| 1.3.2 | Fuel Nozzle | fighter-jet-fuel-nozzle | 20× | 20 | · | part |
| 1.3.3 | Igniter Plug | fighter-jet-igniter | 2× | 2 | · | part |
| 1.4 | High-Pressure Turbine 3 parts | fighter-jet-hp-turbine | 1× | 1 | 141 | assembly |
| 1.4.1 | Turbine Disk | fighter-jet-turbine-disk | 1× | 1 | · | part |
| 1.4.2 | Turbine Blade (cooled) | fighter-jet-turbine-blade | 80× | 80 | · | part |
| 1.4.3 | Nozzle Guide Vane | fighter-jet-nozzle-guide-vane | 60× | 60 | · | part |
| 1.5 | Low-Pressure Turbine | fighter-jet-lp-turbine | 1× | 1 | · | part |
| 1.6 | Afterburner 3 parts | fighter-jet-afterburner | 1× | 1 | 8 | assembly |
| 1.6.1 | Fuel Spray Bar | fighter-jet-spray-bar | 6× | 6 | · | part |
| 1.6.2 | Flame Holder | fighter-jet-flame-holder | 1× | 1 | · | part |
| 1.6.3 | Afterburner Liner | fighter-jet-afterburner-liner | 1× | 1 | · | part |
| 1.7 | Variable Exhaust Nozzle 3 parts | fighter-jet-exhaust-nozzle | 1× | 1 | 21 | assembly |
| 1.7.1 | Nozzle Petal | fighter-jet-nozzle-petal | 16× | 16 | · | part |
| 1.7.2 | Nozzle Actuator | fighter-jet-nozzle-actuator | 4× | 4 | · | part |
| 1.7.3 | Nozzle Sync Ring | fighter-jet-nozzle-ring | 1× | 1 | · | part |
| 1.8 | FADEC Engine Control 4 parts | fighter-jet-fadec | 1× | 1 | 232 | assembly |
| 1.8.1 | Bare PCB | pcb-bare | 2× | 2 | · | part |
| 1.8.2 | Microcontroller | mcu | 2× | 2 | · | part |
| 1.8.3 | SMD Passive (R/C/L) | smd-passives | 220× | 220 | · | part |
| 1.8.4 | Connector | connector | 8× | 8 | · | part |
| 1.9 | Ball Bearing | ball-bearing | 8× | 8 | · | part |
| 2 | Airframe 7 parts | fighter-jet-airframe | 1× | 1 | 19 | assembly |
| 2.1 | Fuselage Structure | fighter-jet-fuselage-structure | 1× | 1 | · | part |
| 2.2 | Wing 4 parts | fighter-jet-wing | 2× | 2 | 5 | assembly |
| 2.2.1 | Wing Spar | fighter-jet-wing-spar | 2× | 4 | · | part |
| 2.2.2 | Wing Skin | fighter-jet-wing-skin | 1× | 2 | · | part |
| 2.2.3 | Leading-Edge Flap | fighter-jet-leading-edge-flap | 1× | 2 | · | part |
| 2.2.4 | Aileron | fighter-jet-aileron | 1× | 2 | · | part |
| 2.3 | Vertical Tail | fighter-jet-vertical-tail | 2× | 2 | · | part |
| 2.4 | All-Moving Horizontal Tail | fighter-jet-horizontal-tail | 2× | 2 | · | part |
| 2.5 | Air Intake (S-duct) | fighter-jet-air-intake | 2× | 2 | · | part |
| 2.6 | Radar-Absorbent Coating | fighter-jet-ram-coating | 1× | 1 | · | part |
| 2.7 | Fastener Set | fastener-set | 1× | 1 | · | part |
| 3 | Cockpit & Life Support 7 parts | fighter-jet-cockpit | 1× | 1 | 24 | assembly |
| 3.1 | Ejection Seat 4 parts | fighter-jet-ejection-seat | 1× | 1 | 4 | assembly |
| 3.1.1 | Seat Bucket | fighter-jet-seat-bucket | 1× | 1 | · | part |
| 3.1.2 | Rocket Catapult | fighter-jet-rocket-catapult | 1× | 1 | · | part |
| 3.1.3 | Seat Parachute | fighter-jet-seat-parachute | 1× | 1 | · | part |
| 3.1.4 | Drogue Gun | fighter-jet-drogue-gun | 1× | 1 | · | part |
| 3.2 | Bubble Canopy | fighter-jet-canopy | 1× | 1 | · | part |
| 3.3 | Head-Up Display 4 parts | fighter-jet-hud | 1× | 1 | 4 | assembly |
| 3.3.1 | LCD Panel | lcd-panel | 1× | 1 | · | part |
| 3.3.2 | Combiner Glass | fighter-jet-combiner-glass | 1× | 1 | · | part |
| 3.3.3 | Bare PCB | pcb-bare | 1× | 1 | · | part |
| 3.3.4 | Microcontroller | mcu | 1× | 1 | · | part |
| 3.4 | Multifunction Display 4 parts | fighter-jet-mfd | 3× | 3 | 4 | assembly |
| 3.4.1 | LCD Panel | lcd-panel | 1× | 3 | · | part |
| 3.4.2 | Touch Digitizer | touch-digitizer | 1× | 3 | · | part |
| 3.4.3 | Bare PCB | pcb-bare | 1× | 3 | · | part |
| 3.4.4 | Microcontroller | mcu | 1× | 3 | · | part |
| 3.5 | HOTAS Controls | fighter-jet-hotas | 1× | 1 | · | part |
| 3.6 | Onboard Oxygen Generator | fighter-jet-obogs | 1× | 1 | · | part |
| 3.7 | Helmet-Mounted Display | fighter-jet-helmet-display | 1× | 1 | · | part |
| 4 | Avionics Suite 6 parts | fighter-jet-avionics | 1× | 1 | 2,185 | assembly |
| 4.1 | AESA Radar 4 parts | fighter-jet-aesa-radar | 1× | 1 | 1,425 | assembly |
| 4.1.1 | T/R Module | fighter-jet-tr-module | 1000× | 1,000 | · | part |
| 4.1.2 | Radar Backplane | fighter-jet-radar-backplane | 1× | 1 | · | part |
| 4.1.3 | Radar Signal Processor 4 parts + deeper › | fighter-jet-radar-processor | 1× | 1 | 423 | assembly |
| 4.1.4 | Power Supply | power-supply | 1× | 1 | · | part |
| 4.2 | Infrared Search & Track | fighter-jet-irst | 1× | 1 | · | part |
| 4.3 | Electronic Warfare Suite 3 parts | fighter-jet-ew-suite | 1× | 1 | 3 | assembly |
| 4.3.1 | Radar Warning Receiver | fighter-jet-rwr | 1× | 1 | · | part |
| 4.3.2 | Self-Protection Jammer | fighter-jet-jammer | 1× | 1 | · | part |
| 4.3.3 | Chaff/Flare Dispenser | fighter-jet-countermeasure-dispenser | 1× | 1 | · | part |
| 4.4 | Mission Computer 4 parts | fighter-jet-mission-computer | 2× | 2 | 377 | assembly |
| 4.4.1 | Bare PCB | pcb-bare | 2× | 4 | · | part |
| 4.4.2 | Compute SoC Module | soc-module | 1× | 2 | · | part |
| 4.4.3 | SMD Passive (R/C/L) | smd-passives | 350× | 700 | · | part |
| 4.4.4 | Connector | connector | 24× | 48 | · | part |
| 4.5 | INS/GPS Navigator | fighter-jet-ins-gps | 1× | 1 | · | part |
| 4.6 | Tactical Datalink | fighter-jet-datalink | 1× | 1 | · | part |
| 5 | Fly-by-Wire Flight Controls 4 parts | fighter-jet-flight-controls | 1× | 1 | 1,237 | assembly |
| 5.1 | Flight Control Computer 4 parts | fighter-jet-flight-control-computer | 4× | 4 | 302 | assembly |
| 5.1.1 | Bare PCB | pcb-bare | 2× | 8 | · | part |
| 5.1.2 | Microcontroller | mcu | 2× | 8 | · | part |
| 5.1.3 | SMD Passive (R/C/L) | smd-passives | 280× | 1,120 | · | part |
| 5.1.4 | Connector | connector | 18× | 72 | · | part |
| 5.2 | Surface Hydraulic Actuator 3 parts | fighter-jet-control-actuator | 8× | 8 | 3 | assembly |
| 5.2.1 | Actuator Cylinder | heavy-lift-helicopter-actuator-cylinder | 1× | 8 | · | part |
| 5.2.2 | Servo Valve | heavy-lift-helicopter-servo-valve | 1× | 8 | · | part |
| 5.2.3 | O-Ring Set | oring-set | 1× | 8 | · | part |
| 5.3 | Air Data Computer | fighter-jet-air-data-computer | 2× | 2 | · | part |
| 5.4 | IMU (6-axis) | imu | 3× | 3 | · | part |
| 6 | Landing Gear 6 parts | fighter-jet-landing-gear | 1× | 1 | 21 | assembly |
| 6.1 | Main Gear Leg | fighter-jet-main-gear | 2× | 2 | · | part |
| 6.2 | Nose Gear Leg | fighter-jet-nose-gear | 1× | 1 | · | part |
| 6.3 | Oleo-Pneumatic Strut 4 parts | heavy-lift-helicopter-oleo-strut | 3× | 3 | 4 | assembly |
| 6.3.1 | Strut Cylinder | heavy-lift-helicopter-strut-cylinder | 1× | 3 | · | part |
| 6.3.2 | Strut Piston | heavy-lift-helicopter-strut-piston | 1× | 3 | · | part |
| 6.3.3 | O-Ring Set | oring-set | 1× | 3 | · | part |
| 6.3.4 | Oil Seal | oil-seal | 1× | 3 | · | part |
| 6.4 | Wheel & Tire | fighter-jet-gear-wheel | 3× | 3 | · | part |
| 6.5 | Carbon Wheel Brake | fighter-jet-gear-brake | 2× | 2 | · | part |
| 6.6 | Arrestor Hook | fighter-jet-arrestor-hook | 1× | 1 | · | part |
| 7 | Fuel System 5 parts | fighter-jet-fuel-system | 1× | 1 | 15 | assembly |
| 7.1 | Internal Fuel Tank | fighter-jet-fuel-tank | 4× | 4 | · | part |
| 7.2 | Boost Fuel Pump | heavy-lift-helicopter-fuel-pump | 4× | 4 | · | part |
| 7.3 | Fuel Filter | heavy-lift-helicopter-fuel-filter | 2× | 2 | · | part |
| 7.4 | Fuel Tank Inerting System | fighter-jet-fuel-inerting | 1× | 1 | · | part |
| 7.5 | Pressure Sensor | pressure-sensor | 4× | 4 | · | part |
| 8 | Weapon System 5 parts | fighter-jet-weapon-system | 1× | 1 | 176 | assembly |
| 8.1 | Rotary Cannon 4 parts | fighter-jet-cannon | 1× | 1 | 9 | assembly |
| 8.1.1 | Gun Barrel | fighter-jet-gun-barrel | 6× | 6 | · | part |
| 8.1.2 | Barrel Rotor | fighter-jet-gun-rotor | 1× | 1 | · | part |
| 8.1.3 | Gun Drive Motor | fighter-jet-gun-drive-motor | 1× | 1 | · | part |
| 8.1.4 | Ammunition Drum | fighter-jet-ammo-drum | 1× | 1 | · | part |
| 8.2 | Wing Hardpoint | fighter-jet-hardpoint | 11× | 11 | · | part |
| 8.3 | Internal Weapons Bay 3 parts | fighter-jet-internal-bay | 2× | 2 | 6 | assembly |
| 8.3.1 | Bay Door | fighter-jet-bay-door | 2× | 4 | · | part |
| 8.3.2 | Bay Door Actuator | fighter-jet-bay-actuator | 2× | 4 | · | part |
| 8.3.3 | Ejector Rack | fighter-jet-ejector-rack | 2× | 4 | · | part |
| 8.4 | Stores Management System 4 parts | fighter-jet-stores-management | 1× | 1 | 138 | assembly |
| 8.4.1 | Bare PCB | pcb-bare | 1× | 1 | · | part |
| 8.4.2 | Microcontroller | mcu | 1× | 1 | · | part |
| 8.4.3 | SMD Passive (R/C/L) | smd-passives | 120× | 120 | · | part |
| 8.4.4 | Connector | connector | 16× | 16 | · | part |
| 8.5 | Missile Launch Rail | fighter-jet-missile-launcher | 6× | 6 | · | part |
| 9 | Hydraulic System 4 parts | fighter-jet-hydraulics | 1× | 1 | 9 | assembly |
| 9.1 | Hydraulic Pump | heavy-lift-helicopter-hydraulic-pump | 2× | 2 | · | part |
| 9.2 | Hydraulic Reservoir | heavy-lift-helicopter-hydraulic-reservoir | 2× | 2 | · | part |
| 9.3 | Hydraulic Manifold | heavy-lift-helicopter-hydraulic-manifold | 1× | 1 | · | part |
| 9.4 | Pressure Sensor | pressure-sensor | 4× | 4 | · | part |
| 10 | Electrical System 5 parts | fighter-jet-electrical | 1× | 1 | 205 | assembly |
| 10.1 | Integrated Drive Generator | fighter-jet-generator | 2× | 2 | · | part |
| 10.2 | Power Distribution Unit 4 parts | fighter-jet-power-distribution | 1× | 1 | 141 | assembly |
| 10.2.1 | Bare PCB | pcb-bare | 1× | 1 | · | part |
| 10.2.2 | Relay | relay | 20× | 20 | · | part |
| 10.2.3 | SMD Passive (R/C/L) | smd-passives | 80× | 80 | · | part |
| 10.2.4 | Connector | connector | 40× | 40 | · | part |
| 10.3 | 12 V Battery | lv-battery | 1× | 1 | · | part |
| 10.4 | Wire Bundle | wire-bundle | 1× | 1 | · | part |
| 10.5 | Connector | connector | 60× | 60 | · | part |
Sourcing: possible vendors
Browse the supplier directory → Prices, MOQ, and lead times are algorithmic estimates, not quotes, and not claims about these companies. Company mappings are curated by keyword; est. price band $200–$100M. How estimates work| Vendor | HQ | Specialty | MOQ | Lead time |
|---|---|---|---|---|
| smithsdetection.com ↗ | London, GB | Security screening | made to order | 24–52 wks |
|
🇺🇸Leidos
leidos.com ↗
|
Reston, US | Security & screening | made to order | 24–52 wks |
|
🇺🇸Rapiscan
rapiscansystems.com ↗
|
Torrance, US | X-ray screening | made to order | 24–52 wks |
|
🇫🇷Thales
thalesgroup.com ↗
|
Paris, FR | Defense electronics | made to order | 24–52 wks |
| baesystems.com ↗ | London, GB | Defense | made to order | 24–52 wks |
899-word article