BOMwiki the bill-of-materials encyclopedia
30,454,201 parts mapped · 193,225 items

You are viewing r135975 of this page, not the current version. Go to current · history

Radial Spillway Gate

Product

Overview

A radial spillway gate, also called a Tainter gate, is a curved steel gate that controls the release of flood water over the crest of a dam spillway. The gate sits between two concrete piers and pivots about a horizontal trunnion pin downstream of the water-retaining face. When closed it holds back the reservoir; when the hoist raises it, water passes underneath in a controlled surface discharge over the spillway crest. Radial gates are the dominant choice for large spillways because the curved face routes the entire water load through the radial arms into the trunnion, so the gate can be very large yet still operated by a modest hoist.

The water-retaining surface is the curved skin plate, a cylindrical steel face whose center of curvature lies exactly on the trunnion pin axis. Because every point of the face is the same distance from the pin, the hydrostatic pressure acting normal to the plate produces a resultant force that points straight at the pin. That geometry is the whole reason the design works.

How it works

Water pressure increases linearly with depth, so the load on the skin plate is largest at the bottom and zero at the surface. The plate alone is thin, so a stiffening grid of horizontal girders and vertical ribs backs it up and collects the distributed pressure into a few concentrated line loads. The horizontal girders carry these loads across the span to the two sets of radial arms.

To open the gate, the motor drives the gearbox and rope drums, which reel in the wire ropes attached to the gate. The whole gate rotates about the trunnion pin, lifting its lower lip clear of the sill and letting water spill underneath. Discharge is metered by the gate opening and the reservoir level, which the level sensor feeds to the control system so releases can track the inflow hydrograph.

Trunnion and load path

The defining feature of a radial gate is its load path. Because the face is cylindrical about the trunnion pin, the resultant of all the hydrostatic pressure passes through the pin axis. The two arm struts of each set act almost purely in compression, carrying that resultant from the girders to the trunnion hub. The pin then reacts the entire thrust, which can reach 3 to 40 MN depending on gate size, in double shear, and passes it through the trunnion bracket and embedded girder into the concrete pier.

Two consequences follow. First, the thrust line passes through the pivot, so it creates almost no moment about the trunnion. The hoist therefore only has to overcome the gate self-weight, the trunnion friction, and the seal friction, not the water load. That is why a gate retaining tens of meganewtons can be lifted by a hoist rated at a few hundred kilonewtons per arm. Second, the trunnion bushing runs at very high contact pressure but low sliding speed, so a self-lubricating aluminium-bronze bushing is used and the friction coefficient is kept low to limit hoist load.

Materials and construction

The skin plate, girders, ribs, and arms are fabricated from weldable structural steel, typically ASTM A572 Grade 50 or S355J2, and shop-assembled in segments that are field-bolted at the arm flanges. The trunnion pin is a forged alloy steel pin, 200 to 500 mm in diameter, machined and ground to run in the bronze bushings. All submerged steel carries a zinc-rich epoxy and polyurethane coating, since the steel cycles between wet and dry and corrosion at the trunnion or seals is a common cause of hard operation.

Sealing is by rubber. Music-note side seals run up each side of the gate and are pressed by water pressure against the polished stainless rubbing plates embedded in the piers. A J-seal along the lower lip seats on the sill plate when closed. The seals are held by clamp bars that set the seal projection, which is adjusted in the field to balance tight sealing against hoist friction.

The trunnion reaction is anchored into the pier by the anchorage, usually a combination of the embedded trunnion girder and post-tensioned anchor tendons that prestress the concrete so it stays in compression under the gate thrust.

Variants

The hoist can be a wire-rope drum hoist, as detailed here, or a pair of hydraulic cylinders acting on the arms. Cylinders give precise position control and are common on newer or remotely operated gates, while rope hoists are simple and easy to service. Submergible designs place the trunnion below tailwater for very large gates. Cold-climate gates add the de-icing system, with trace heaters along the seals and trunnion so ice does not freeze the gate to the sill or seize the bushing. Most large gates are automated through the control system, with a PLC, position encoder, and limit switches that hold a target opening or follow a reservoir-level schedule.

Common failures

The trunnion is the critical element. If the bushing corrodes or loses lubrication, friction rises sharply, the hoist can stall, and in severe cases the arms have buckled when the bushing seized and the rising hoist force overloaded them. Regular greasing through the grease fittings and friction monitoring are essential. Seal wear and hardening cause leakage and higher operating effort; seals are wear items replaced on a schedule. Corrosion of the anchor tendons or loss of prestress threatens the load path into the pier and is checked by inspection and tendon lift-off testing. Wire-rope corrosion, brake faults, and limit-switch failures are the typical hoist problems, which is why the brake is spring-set so the gate holds position on power loss.

Bill of materials for Radial Spillway Gate

10 top-level lines as of r135975
# Item / sub-assembly Part no. Qty/assy Ext. qty Parts Type
1 Skin Plate Assembly 6 parts radial-spillway-gate-skin-plate-assy 1× 1 0 assembly
2 Radial Arm Set 4 parts radial-spillway-gate-arm-assy 2× 2 0 assembly
3 Trunnion Assembly 7 parts radial-spillway-gate-trunnion-assy 2× 2 0 assembly
4 Seal Assembly 5 parts radial-spillway-gate-seal-assy 1× 1 0 assembly
5 Hoist System 8 parts radial-spillway-gate-hoist-assy 1× 1 0 assembly
6 Trunnion Anchorage 4 parts radial-spillway-gate-anchorage-assy 2× 2 0 assembly
7 Pier Guide Assembly 4 parts radial-spillway-gate-pier-guide-assy 2× 2 0 assembly
8 Control System 7 parts radial-spillway-gate-control-assy 1× 1 0 assembly
9 De-Icing System 3 parts radial-spillway-gate-deice-assy 1× 1 0 assembly
10 Fastener Set fastener-set 1× 1 · part

1,160-word article