BOMwiki the bill-of-materials encyclopedia
30,454,201 parts mapped · 193,225 items

You are viewing r157475 of this page, not the current version. Go to current · history

Sluice Gate

Product

Overview

A sluice gate is a sliding plate that opens and closes an opening in a canal, dam, channel or treatment basin to control how much water passes. The plate, called the leaf, slides up and down inside a fixed frame set into the concrete wall. Lower the leaf and it seals the opening; raise it and water flows under or through. Unlike a butterfly or knife valve in a closed pipe, a sluice gate works on an open or partly open waterway, and it is sized in metres of opening rather than in pipe diameter.

The product here is a fabricated rising-stem gate of the kind used on irrigation canals, dam outlet works and wastewater treatment plants. Its main groups are the Gate Leaf, the Guide Frame it slides in, the Seal Set that limit leakage, the Stem Assembly that drives it, the Headstock and Lift Mechanism that an operator turns, an optional Electric Actuator for remote control, and the Anchorage that ties everything into the structure.

How it works

Turning the Handwheel spins a bronze Lift Nut through a gear reduction. The nut threads onto the Threaded Stem, so as the nut turns the stem and the leaf attached to it move up or down. On a rising-stem gate the stem rises out of the headstock as the gate opens, and the exposed thread doubles as a position indicator. On a non-rising-stem gate the stem turns in place and a threaded lift nut built into the leaf travels along it, which suits cramped or submerged installations where a tall rising stem will not fit.

As the leaf reaches the closed position the Wedge Block faces ride up against matching wedges on the frame. They drive the leaf hard against the Frame Seal Seat, compressing the rubber seals and pulling leakage down. The same wedges must release cleanly on opening, which is why unseating a gate often needs as much thrust as seating it.

A key distinction is seating versus unseating head. Seating head pushes the leaf into the frame, so the seals are pressed tighter and the gate seals well. Unseating head pushes the leaf away from the frame, so the leaf must be held against its backing guides and the seals work harder. A gate rated for high seating head may carry a much lower unseating rating, and the data sheet lists both.

Subsystems

The Gate Leaf is a Skin Plate backed by horizontal Horizontal Stiffener Rib members that keep it from bowing under head. The Guide Frame embeds two Frame Jamb members, a Frame Head and an Invert Sill the leaf lands on. The Seal Set group carries side J-Seal strips, a top seal and a Bottom Seal at the invert, each held by a Seal Retainer Bar. The Headstock holds the Thrust Bearing that takes the axial load, plus a Position Indicator. Where the gate is automated, the Electric Actuator adds a motor, a worm Helical Gear Pair and a Control Board with Limit Switch and Position Sensor feedback to the plant SCADA.

Materials and construction

Frames and leaves are built either as grey cast iron, which is cheap and stiff for small gates, or as fabricated 304 or 316 stainless steel for corrosion service in wastewater, brackish water and coastal sites. Seal seats and the invert sill are faced in 316 stainless or bronze so they stay smooth against the rubber. Seals are EPDM for clean water or neoprene where oils and grease are present. Stems are stainless with rolled or cut ACME threads, sized so the unsupported length will not buckle under unseating thrust; tall stems run through Stem Guide Bracket brackets at intervals. Sliding side guides are bronze or UHMWPE so the leaf moves without galling.

Variants

Gates split by mounting and by stem. Wall-mounted gates bolt to a finished concrete face through an Embedment Plate; channel gates set directly into a formed slot. Flush-bottom gates seal the invert flat so sludge does not collect on the sill, which matters in wastewater channels. Weir gates and overflow gates spill water over the top of the leaf rather than under it. Drive options run from a simple handwheel, to a bench stand or floor stand for headroom, to a full electric Electric Actuator with Torque Limiter protection and remote operation.

Common failures

The usual problems are leakage and binding. Seal leakage comes from a hardened or torn J-Seal, from a Invert Sill worn by grit, or from a frame that has drifted out of plane during grouting. Binding comes from a bent stem, a dry Lift Nut, or debris jammed in the guides; an electric actuator will trip its Torque Limiter before it damages the stem. Corrosion attacks cast iron gates first at the waterline and at the fastener heads, which is why stainless or coated hardware is specified in aggressive water.

Selection and installation

Pick the gate by clear opening, by the higher of the seating and unseating heads, and by the leakage class the plant must meet under AWWA C560 for cast iron or C561 for stainless. Confirm the Anchor Bolt pattern against the wall opening and set the Embedment Plate true before grout. Install the frame plumb and square, shim it with Grout Shim pieces, grout it, then fit the leaf and adjust the Wedge Block faces so the seals compress evenly. Cycle the gate through full travel, check leakage at the rated head, and set the actuator limits and torque trips before handover.

Bill of materials for Sluice Gate

8 top-level lines as of r157475
# Item / sub-assembly Part no. Qty/assy Ext. qty Parts Type
1 Gate Leaf 8 parts sluice-gate-leaf 1× 1 0 assembly
2 Guide Frame 7 parts sluice-gate-guide-frame 1× 1 0 assembly
3 Seal Set 5 parts sluice-gate-seals 1× 1 0 assembly
4 Stem Assembly 5 parts sluice-gate-stem-assembly 1× 1 0 assembly
5 Headstock 6 parts sluice-gate-headstock 1× 1 0 assembly
6 Lift Mechanism 6 parts sluice-gate-lift-mech 1× 1 0 assembly
7 Electric Actuator 9 parts sluice-gate-actuator 1× 1 0 assembly
8 Anchorage 4 parts sluice-gate-anchorage 1× 1 0 assembly

997-word article