BOMwiki the bill-of-materials encyclopedia
30,454,201 parts mapped · 193,225 items

You are viewing r14912 of this page, not the current version. Go to current · history

Bladeless Fan

Product

Overview

A bladeless fan is a tower fan that hides its impeller inside the base and projects a smooth, steady stream of air out of a hollow loop with no visible moving parts. The name is a marketing term rather than an engineering one, because the fan does contain a fast-spinning impeller, just one the user never touches or sees. The benefit is real: there is no exposed blade to clean or to catch fingers, the airflow is far less choppy than a bladed fan, and the loop can oscillate quietly. A typical unit stands 70 to 110 cm tall, draws 20 to 65 W, and projects 300 to 700 CFM at the loop face.

Air enters through the Base Assembly, is pressurised by the Impeller Assembly, and is released through a thin slot around the inside of the Air Loop Assembly. A Control Board runs the motor and the user interface, a Oscillation Assembly sweeps the loop side to side, and a Acoustic Assembly suppresses the whine that a high-speed impeller would otherwise make audible.

How it works

The physics is the same air-multiplier effect used in some industrial blowers. The Impeller Assembly pulls room air through the Intake Grille and pressurises it inside the base. That pressurised air is fed up into the hollow Air Loop Assembly, which is sealed except for a continuous slot about 1.3 mm wide running around the inner edge of the Loop Rear Shell. Forcing the air through that narrow gap accelerates it into a thin, fast sheet.

The inner face of the loop is shaped by the Airfoil Ramp into a curved ramp, much like an aircraft wing. As the slot jet hugs that curved surface it stays attached and turns to flow across the open centre of the ring, an effect called the Coanda effect. The fast-moving sheet drags the still air immediately around it into motion through viscous shear, a process called entrainment. Air just behind the loop is also drawn forward by the low pressure the jet leaves behind, which is called induction. Between entrainment in front and induction behind, the volume of air leaving the front of the loop is roughly fifteen times the volume the impeller actually pushed through the slot. That is the multiplication that lets a modest impeller deliver a large, smooth column of moving air.

Impeller and motor

The pressure that drives the whole effect comes from the Impeller Assembly. Its Impeller Wheel is a glass-filled nylon mixed-flow impeller, a shape between a pure axial fan and a centrifugal blower, chosen because it produces both useful flow and the static pressure needed to push air through the narrow slot. A fixed Diffuser Stage downstream straightens the swirling discharge and recovers more of it as pressure. The wheel can turn up to about 30000 RPM, far faster than any open blade could safely run, which is exactly why it has to be enclosed in the Motor Bucket.

Driving it is a Brushless DC Motor, a brushless DC motor built from a Stator Assembly and a permanent-magnet Rotor Assembly running on two Ball Bearing supports around a balanced Motor Shaft. Three Hall Sensor devices report the rotor angle so the controller knows when to switch each phase. A brushless motor is used instead of the cheap shaded-pole motor in a Box Fan for three reasons: it can reach the very high speed the impeller needs, it is efficient enough to keep total draw under about 65 W, and its speed can be set precisely in software. The motor hangs in a rubber Motor Mount so its vibration does not reach the Base Shell.

Base and oscillation

The Base Assembly does more than hold the fan up. Its Base Shell forms the pressurised plenum that feeds the loop, the Intake Grille admits room air, and a washable Intake Filter keeps dust off the impeller, which matters because deposits unbalance a wheel spinning at 30000 RPM. A cast iron Base Ballast at the bottom lowers the centre of gravity so the tall fan does not tip, and a Base Foot Pad ring grips the floor.

Oscillation is handled by the Oscillation Assembly. A Oscillation Stepper Motor drives a Helical Gear Pair reduction that rotates the Turntable carrying the loop and base through a sweep the user can set between 70 and 350 degrees. Because the air column travels up through the rotating joint, a Slip Coupling keeps the path sealed while the platter turns, and a Coil Spring holds the mechanism against backlash so the sweep is smooth.

Electronics and acoustics

The Control Board carries the Microcontroller that runs the fan, the Inverter Stage that commutates the brushless motor, and a Power Supply that converts mains to the DC rails. SMD Passive (R/C/L) handle filtering and timing. The user controls the fan through a Touch Panel on the base and a handheld remote read by the IR Receiver. Ten speed steps and a sleep timer are all set in software by varying the motor speed, which is why a bladeless fan can be turned down far quieter than a bladed fan with mechanical speed taps.

Noise is the main engineering challenge, because a 30000 RPM impeller produces a sharp blade-pass tone that would be unpleasant if left untreated. The Acoustic Assembly addresses it. A Helmholtz Cavity is tuned to cancel the dominant tone the way a bottle neck resonates at one pitch, an open-cell Acoustic Liner absorbs the broadband hiss along the air path, and an Inlet Baffle straightens incoming air so the impeller meets clean flow rather than turbulence. Together these keep a well-designed unit between 40 and 58 dB across its range, quiet enough to run in a bedroom at low speed. The trade-off against a Box Fan is cost: the brushless motor, the precision loop tooling, and the acoustic work put a bladeless fan at several times the price for similar room airflow.

Bill of materials for Bladeless Fan

8 top-level lines as of r14912
# Item / sub-assembly Part no. Qty/assy Ext. qty Parts Type
1 Air Loop Assembly 4 parts bladeless-fan-loop-assembly 1× 1 0 assembly
2 Base Assembly 5 parts bladeless-fan-base-assembly 1× 1 0 assembly
3 Impeller Assembly 5 parts bladeless-fan-impeller-assembly 1× 1 0 assembly
4 Oscillation Assembly 5 parts bladeless-fan-oscillation-assembly 1× 1 0 assembly
5 Control Board 8 parts bladeless-fan-control-board 1× 1 0 assembly
6 Acoustic Assembly 3 parts bladeless-fan-acoustic-assembly 1× 1 0 assembly
7 Power Cord Assembly 3 parts bladeless-fan-cord-assembly 1× 1 0 assembly
8 Fastener Set fastener-set 1× 1 · part

1,070-word article