BOMwiki the bill-of-materials encyclopedia
30,454,201 parts mapped · 193,225 items

You are viewing r49820 of this page, not the current version. Go to current · history

Textile Draw Frame

Product

Overview

A draw frame is the machine that makes spinning-room sliver even. The card delivers a sliver that is reasonably clean but uneven in thickness and full of hooked and crossed fibers. If that sliver went straight to spinning the yarn would vary in count and strength along its length. The draw frame fixes this in two ways at once: it doubles several slivers together so their thick and thin places average out, and it drafts the combined strand back down to a single sliver while straightening the fibers along the way.

Drawing is usually done in one or two passes. The first passage blends and parallelises, and a second passage, often called the finisher draw frame, brings the evenness up to the level spinning needs. On a modern machine the second pass carries an auto-leveller that watches the strand and corrects its thickness as it runs, which is what lets one draw frame replace the several passages older machines needed.

Doubling and drafting

Six to eight slivers from the Sliver Creel & Feed feed into the machine side by side. Doubling is the simple part: a thin place in one sliver lands next to a thick place in another, so the combined strand is steadier than any single feed. The Drafting System system then pulls that combined strand out to a fraction of its fed thickness. A set of bottom rollers turn at rising speed from back to front, and the Bottom Drafting Roller front pair runs fastest, so the strand is stretched between the nips. Rubber-covered Top Pressure Roller rollers pressed down by the Top Roller Pressure Arm grip the fibers so the draft acts on every fiber and not just the surface. As the fibers slide past one another in the draft zone their hooks pull straight, which is the other reason drawing matters: straight parallel fibers make stronger, smoother yarn.

The total draft roughly equals the number of doublings, so the sliver that leaves is about the same weight per metre as one that came in, but far more even and far better aligned.

Auto-levelling

The single biggest improvement on a modern draw frame is the Auto-Leveller. At the feed, the doubled slivers pass through a spring-loaded Measuring Funnel whose opening tracks the strand thickness. A Thickness Displacement Sensor reads that opening and turns it into a signal of how much fiber is coming. The Leveller Controller takes this signal, delays it by exactly the time the strand takes to travel from the funnel to the draft zone, and then commands the Draft Correction Servo to vary the draft on the fly. A thick place arriving at the rollers gets drafted more, a thin place less. The output sliver comes out level metre to metre, which is the property that decides the evenness of the final yarn. A delivery funnel checks the levelled strand and logs any residual variation for the quality department.

Coiling and can changing

The even sliver is too bulky and delicate to wind, so it is coiled into a tall can instead. The Sliver Coiler head spins above the can: the sliver passes through a curved Coiler Tube carried on a turning plate, which lays it in overlapping coils, while the Can Turntable rotates the can slowly so each layer shifts and the can fills evenly without tangling. A pair of calender rollers lightly compacts the sliver first so it holds its coil.

When the can reaches its set length the Can Changer swaps it for an empty one automatically. A length counter triggers the change, a pusher arm rolls the full can out onto the transfer track and pulls the next empty can from the magazine into place, all without stopping the machine for long.

Suction and cleanliness

Drafting throws off a lot of fiber fly, and a draw frame runs fast, so the Suction & Waste System system is always on. A fan pulls air through pickup mouths over the rollers and at the broken-end point, carrying fly and trimmings down the ducting to a waste box, while a filter drum separates the fiber so clean air returns to the room. Keeping the draft zone clean matters because a lump of fly drawn into the strand would show up as a fault.

Materials and use

The bottom rollers are case-hardened steel for wear life under constant fiber abrasion, the top rollers carry replaceable rubber cots, and the base and head housing are cast iron because mass damps the vibration that high delivery speeds would otherwise cause. The Machine Control cabinet sets draft, speed and leveller behaviour from a touchscreen and logs evenness data.

Every cotton and blended-fiber spinning mill runs draw frames between carding and the roving or spinning stage. The quality of the sliver they deliver sets a ceiling on the quality of the yarn, so the draw frame, though it is one of the quieter machines in the room, is one of the ones the mill watches most closely.

Bill of materials for Textile Draw Frame

10 top-level lines as of r49820
# Item / sub-assembly Part no. Qty/assy Ext. qty Parts Type
1 Sliver Creel & Feed 5 parts draw-frame-creel 1× 1 0 assembly
2 Drafting System 8 parts draw-frame-drafting 1× 1 0 assembly
3 Auto-Leveller 5 parts draw-frame-autoleveller 1× 1 0 assembly
4 Sliver Coiler 6 parts draw-frame-coiler 1× 1 0 assembly
5 Can Changer 5 parts draw-frame-can-changer 1× 1 0 assembly
6 Suction & Waste System 4 parts draw-frame-suction 1× 1 0 assembly
7 Machine Control 5 parts draw-frame-control 1× 1 0 assembly
8 Machine Frame & Guards 5 parts draw-frame-frame 1× 1 0 assembly
9 Wire Bundle wire-bundle 4× 4 · part
10 Fastener Set fastener-set 6× 6 · part

856-word article